Add RAK811 LoRa Tracker Board by fpistm · Pull Request #254 · stm32duino/Arduino_Core_STM32

fpistm · 2018-05-20T16:31:36Z

Hi @sabas1080,
This PR is the review of your PR #229
I've made several clean and rename the variant RAK811_TRACKER.
RAK811 is a module not really a board but as you mentioned in your PR the board is the
RAK811 LoRa Tracker

~~I've only one doubt about RAM size 16k or 32k? I think it is 32k, could you confirm?~~ --> Sub menu added to be able to select RAM Size (16Kb by default)

Could you test this variant and let me know if it is ok?
Thanks in advance.

Datasheet:
http://docs.rakwireless.com/en/RAK811%20TrackerBoard/Software%20Development/RAK811%20TrackerBoard%20Datasheet%20V1.1.pdf

Github:
https://github.com/RAKWireless/RAK811_BreakBoard

Using RAK 811 Lora Module
Datasheet:
http://docs.rakwireless.com/en/RAK811/Software%20Development/RAK811%C2%A0Lora%C2%A0Module%C2%A0Datasheet%C2%A0V1.3.pdf

http://www.rakwireless.com/en/download/RAK811/Hardware%20Design

sabas1080 · 2018-05-20T18:23:51Z

Hi @fpistm

The SRAM is 16k

Thanks

fpistm · 2018-05-20T18:49:06Z

Ok. Thanks. updated to 16kb of RAM. I read somewhere it was up to 32k maybe a mistake...
You could check with STLink how many RAM the board has really.
Let me know if it is ok.

chaolue · 2018-05-23T22:35:10Z

@fpistm,

May need to research the SRAM size - see https://github.com/Ebiroll/RAK811_BreakBoard

The earlier versions of the board only had 16K ram so stm32l15xx6.ld is default as linker script. If you want to use the full 32K ram you can change this line before copy "ldscript": "/home/olof/rak/STM32L151XBA_FLASH.ld"

fpistm · 2018-05-24T04:50:18Z

@chaolue yes this is what I've read 👍 Maybe I could add a menu to select ramsize.
@sabas1080 have you tested ?

fpistm · 2018-05-24T21:29:51Z

I've added a sub menu to be able to select RAM Size (16Kb by default)

fpistm · 2018-05-28T07:41:35Z

Any news @sabas1080?
I will do a release soon so if this is tested, I could merge and release it.
Thanks in advance

sabas1080 · 2018-05-30T20:37:03Z

Hi @fpistm

I am useing stm32flash and it appears the next information

Using Parser : Raw BINARY
Interface serial_posix: 115200 8E1
Version      : 0x31
Option 1     : 0x00
Option 2     : 0x00
Device ID    : 0x0429 (L1xxx6(8/B)A)
- RAM        : 32KiB  (4096b reserved by bootloader)
- Flash      : 128KiB (sector size: 16x256)
- Option RAM : 16b
- System RAM : 4KiB

fpistm · 2018-05-30T20:42:41Z

So, there is 2 versions. With the ram size menu you can select the right one.
Have you tested this PR?

fpistm · 2018-06-08T08:59:05Z

Hi @sabas1080,
without feedback from you I could not merge it.
So, without news, it will not be in next release 1.3.0

fpistm · 2018-07-09T06:41:59Z

@sabas1080 Any update?

sabas1080 · 2018-07-09T14:45:47Z

I'm going to testing today

sabas1080 · 2018-07-09T20:29:25Z

I have updated to 1.3.0 and

/Library/Arduino15/packages/STM32/hardware/stm32/1.3.0/cores/arduino/stm32/low_power.c: In function 'LowPower_EnableWakeUpPin': /Library/Arduino15/packages/STM32/hardware/stm32/1.3.0/cores/arduino/stm32/low_power.c:98:12: error: 'SYS_WKUP1' undeclared (first use in this function) case SYS_WKUP1 : ^~~~~~~~~ /Library/Arduino15/packages/STM32/hardware/stm32/1.3.0/cores/arduino/stm32/low_power.c:98:12: note: each undeclared identifier is reported only once for each function it appears in /Library/Arduino15/packages/STM32/hardware/stm32/1.3.0/cores/arduino/stm32/low_power.c:108:12: error: 'SYS_WKUP2' undeclared (first use in this function) case SYS_WKUP2 : ^~~~~~~~~ /Library/Arduino15/packages/STM32/hardware/stm32/1.3.0/cores/arduino/stm32/low_power.c:118:12: error: 'SYS_WKUP3' undeclared (first use in this function) case SYS_WKUP3 : ^~~~~~~~~ exit status 1 Error compilando para la tarjeta RAKWireless.

fpistm · 2018-07-09T21:35:02Z

Sounds strange as I've added the PinNamesVar.h
https://github.com/stm32duino/Arduino_Core_STM32/pull/254/files#diff-5ad876594d46b421d0d4c00eb77e42d8

sabas1080 · 2018-07-10T01:24:04Z

now I have the next error

java.io.IOException: Cannot run program /Library/Arduino15/packages/STM32/hardware/stm32/tools/macosx/serial_upload: error=2, No such file or directory

sabas1080 · 2018-07-10T01:43:52Z

it seems to be a path error

fpistm · 2018-07-10T04:56:49Z

So the build is ok but it do not fin the uploader tools.
This is due to your install to use git.
https://github.com/stm32duino/wiki/wiki/Using-git-repository#3-hereafter-2-methods-to-use-git-repository
When using git depending on how and where you put the core you have to update the platform.txt.

fpistm · 2018-07-10T06:15:23Z

Yes. How do you use the core git repo ?

fpistm · 2018-07-10T20:30:36Z

I do not changed tools binaries. So, if it's work before this should always work.

sabas1080 · 2018-07-10T22:07:04Z

Is the version of the binary

My version is

stm32flash 0.5

http://stm32flash.sourceforge.net/

fpistm · 2018-07-11T06:35:35Z

To sum up: build is ok but you cannot flash thanks Serial?
As said there is no change around flash tools. So, if it is ok before I guess this is linked to the board config to ba able to flash through Serial. Bootloader issue ?

sabas1080 · 2018-07-11T17:18:07Z

Build ok, but stmflash version not compatible with chip

fpistm · 2018-07-11T21:06:15Z

Ok so you never flash using stm32flash provided with core tools before?

Regarding stm32flash source:

	/* L1 */
	{0x416, "STM32L1xxx6(8/B)"                , 0x20000800, 0x20004000, 0x08000000, 0x08020000, 16, p_256 , 0x1FF80000, 0x1FF8001F, 0x1FF00000, 0x1FF01000, F_NO_ME},
	{0x429, "STM32L1xxx6(8/B)A"               , 0x20001000, 0x20008000, 0x08000000, 0x08020000, 16, p_256 , 0x1FF80000, 0x1FF8001F, 0x1FF00000, 0x1FF01000, 0},
	{0x427, "STM32L1xxxC"                     , 0x20001000, 0x20008000, 0x08000000, 0x08040000, 16, p_256 , 0x1FF80000, 0x1FF8001F, 0x1FF00000, 0x1FF02000, 0},
	{0x436, "STM32L1xxxD"                     , 0x20001000, 0x2000C000, 0x08000000, 0x08060000, 16, p_256 , 0x1FF80000, 0x1FF8009F, 0x1FF00000, 0x1FF02000, 0},
	{0x437, "STM32L1xxxE"                     , 0x20001000, 0x20014000, 0x08000000, 0x08080000, 16, p_256 , 0x1FF80000, 0x1FF8009F, 0x1FF00000, 0x1FF02000, F_NO_ME},

Device ID : 0x0429 (L1xxx6(8/B)A) is supported.

Have you selected 32kb in the RAM menu? To use the correct linker script (ldscript_xba.ld) as it seems you have - RAM : 32KiB (4096b reserved by bootloader)

There is one issue around L1 on stm32flash:
https://sourceforge.net/p/stm32flash/tickets/92/

I will try to try stm32flash on L1 to see if I reproduce your issue.

Anyway could you test with ST-Link to validate the variant?

sabas1080 · 2018-07-13T17:09:30Z

Now that I remember, I am using this correction

Formlabs/stm32flash@8c4aa65

that's why I have version 5

fpistm · 2018-07-14T18:28:28Z

Ah interesting.
So, it should be fine to build STM32flash with this fix.
Anyway, what is the status of this variant?
Is it ok from your point of view?

sabas1080 · 2018-07-14T19:09:32Z

Yes, it should build STM32flash with this fix
Working variant blink and serial

sabas1080 · 2018-07-15T03:53:41Z

I have an error with next code

void setup() {
    pinMode(LED_BUILTIN,OUTPUT);//PB_6  //CRF3
    delay(200);
    digitalWrite(LED_BUILTIN,HIGH);
    delay(500);
    digitalWrite(LED_BUILTIN,LOW);
    delay(500); 
    
}

void loop() {

}

led stays on

fpistm · 2018-07-15T06:30:18Z

If the LED is connected to 3.3V, putting LOW on the pin set the LED ON.

Ex on the DISCO L475 IOT:

Putting LOW set the LD4 on

sabas1080 · 2018-07-15T18:46:53Z

Yes, LED is connected to 3.3v

fpistm · 2018-07-15T20:35:44Z

So this is normal :)

fpistm · 2018-07-16T08:32:11Z

About STM32Flash issue.
There will be 2 solutions:
1- Update it with the Fix and rebuild all host OS binaries (Windows/linux/Mac)
2- Unified tools used to flash. It should be possible to use STM32CubeProgrammer CLI. See stm32duino/Arduino_Tools#23

Think the 2nd is the best solution as it support all STM32 Series.

sabas1080 · 2018-07-16T15:02:24Z

I'm going to try the second option

sabas1080 · 2018-07-16T16:40:32Z

I'm trying with STM32CubeProgrammer and i have error de protection

10:16:49 : Serial Port cu.SLAB_USBtoUART is successfully opened.
10:16:49 : Sending init command: 
10:16:49 : byte 0x7F sent successfully to target
10:16:49 : Received response from target: 0x79
10:16:49 : Activating device: OK
10:16:49 : Sending GetID command and its XOR:
10:16:49 : byte 0x02 sent successfully to target
10:16:49 : byte 0xFD sent successfully to target
10:16:49 : Received response from target: 0x79
10:16:49 : Received response from target: 0x01042979
10:16:49 : Chip ID: 0x429 
10:16:49 : Sending Get command and its XOR:
10:16:49 : byte 0x00 sent successfully to target
10:16:49 : byte 0xFF sent successfully to target
10:16:49 : Received response from target: 0x79
10:16:49 : Received response from target: 0x0b
10:16:49 : size of bytes in the response: 11
10:16:49 : Received response from target: 0x31000102112131446373829279
10:16:49 : Full received response: 0b31000102112131446373829279
10:16:49 : byte 0x11 sent successfully to target
10:16:49 : byte 0xEE sent successfully to target
10:16:49 : data sent successfully to target: 0x08000000
10:16:49 : byte 0x08 sent successfully to target
10:16:49 : byte 0x00 sent successfully to target
10:16:49 : byte 0xFF sent successfully to target
10:16:49 : Sending GetID command and its XOR:
10:16:49 : byte 0x02 sent successfully to target
10:16:49 : byte 0xFD sent successfully to target
10:16:49 : Received response from target: 0x79
10:16:49 : Received response from target: 0x01042979
10:16:49 : byte 0x11 sent successfully to target
10:16:49 : byte 0xEE sent successfully to target
10:16:49 : data sent successfully to target: 0x08000000
10:16:49 : byte 0x08 sent successfully to target
10:16:49 : byte 0x00 sent successfully to target
10:16:49 : byte 0xFF sent successfully to target
10:16:49 : Sending Read command and its XOR:
10:16:49 : byte 0x11 sent successfully to target
10:16:49 : byte 0xEE sent successfully to target
10:16:49 : Received response from target: 0x79
10:16:49 : Sending Read address and its checksum:
10:16:49 : data sent successfully to target: 0x40023c1c
10:16:49 : byte 0x62 sent successfully to target
10:16:49 : Received response from target: 0x79
10:16:49 : Sending number of bytes to be read - 1 and its checksum:
10:16:49 : data sent successfully to target: 0x03
10:16:49 : byte 0xFC sent successfully to target
10:16:49 : Received response from target: 0x1f
10:16:49 : Error: Number of bytes to be be read at address: 0x40023C1C not acknowledged!
10:16:49 : Sending Read command and its XOR:
10:16:49 : byte 0x11 sent successfully to target
10:16:49 : byte 0xEE sent successfully to target
10:16:49 : Received response from target: 0x1f
10:16:49 : Error: READ command not acknowledged at address: 0x40023C1C
10:16:49 : byte 0x11 sent successfully to target
10:16:49 : byte 0xEE sent successfully to target
10:16:49 : data sent successfully to target: 0x08000000
10:16:49 : byte 0x08 sent successfully to target
10:16:53 : Disabling memory Read Protection...
10:16:53 : Sending read unprotect command and its XOR:
10:16:53 : byte 0x92 sent successfully to target
10:16:53 : byte 0x6D sent successfully to target
10:16:53 : Received response from target: 0x1f
10:16:53 : Error: Disabling memory Read Protection failed
10:17:09 : Serial Port cu.SLAB_USBtoUART is successfully opened.
10:17:09 : Sending init command: 
10:17:09 : byte 0x7F sent successfully to target
10:17:09 : Received response from target: 0x1f
10:17:09 : Error: Activating device: KO. Please, verify the boot mode configuration and check the serial port configuration. Reset your device then try again... 
10:17:17 : Serial Port cu.SLAB_USBtoUART is successfully opened.
10:17:17 : Sending init command: 
10:17:17 : byte 0x7F sent successfully to target
10:17:18 : No response from target received
10:17:18 : Error: Activating device: KO. Please, verify the boot mode configuration and check the serial port configuration. Reset your device then try again... 
10:17:21 : Serial Port cu.SLAB_USBtoUART is successfully opened.
10:17:21 : Sending init command: 
10:17:21 : byte 0x7F sent successfully to target
10:17:21 : Received response from target: 0x1f
10:17:21 : Error: Activating device: KO. Please, verify the boot mode configuration and check the serial port configuration. Reset your device then try again... 
10:18:34 : Read File: /Users/sabas/Documents/proyectoshd/RAK811WithCoreArduino/ttn/ttn.ino.RAK811.hex
10:18:34 : Number of segments: 1
10:18:34 : segment[0]: address= 0x8000000, size= 0x80C4
10:18:49 : Serial Port cu.SLAB_USBtoUART is successfully opened.
10:18:49 : Sending init command: 
10:18:49 : byte 0x7F sent successfully to target
10:18:50 : No response from target received
10:18:50 : Error: Activating device: KO. Please, verify the boot mode configuration and check the serial port configuration. Reset your device then try again... 
10:18:59 : Serial Port cu.SLAB_USBtoUART is successfully opened.
10:18:59 : Sending init command: 
10:18:59 : byte 0x7F sent successfully to target
10:18:59 : Received response from target: 0x79
10:18:59 : Activating device: OK
10:18:59 : Sending GetID command and its XOR:
10:18:59 : byte 0x02 sent successfully to target
10:18:59 : byte 0xFD sent successfully to target
10:18:59 : Received response from target: 0x79
10:18:59 : Received response from target: 0x01042979
10:18:59 : Chip ID: 0x429 
10:18:59 : Sending Get command and its XOR:
10:18:59 : byte 0x00 sent successfully to target
10:18:59 : byte 0xFF sent successfully to target
10:18:59 : Received response from target: 0x79
10:18:59 : Received response from target: 0x0b
10:18:59 : size of bytes in the response: 11
10:18:59 : Received response from target: 0x31000102112131446373829279
10:18:59 : Full received response: 0b31000102112131446373829279
10:18:59 : byte 0x11 sent successfully to target
10:18:59 : byte 0xEE sent successfully to target
10:18:59 : data sent successfully to target: 0x08000000
10:18:59 : byte 0x08 sent successfully to target
10:18:59 : byte 0x00 sent successfully to target
10:18:59 : byte 0xFF sent successfully to target
10:18:59 : Sending GetID command and its XOR:
10:18:59 : byte 0x02 sent successfully to target
10:18:59 : byte 0xFD sent successfully to target
10:18:59 : Received response from target: 0x79
10:18:59 : Received response from target: 0x01042979
10:18:59 : byte 0x11 sent successfully to target
10:18:59 : byte 0xEE sent successfully to target
10:18:59 : data sent successfully to target: 0x08000000
10:18:59 : byte 0x08 sent successfully to target
10:18:59 : byte 0x00 sent successfully to target
10:18:59 : byte 0xFF sent successfully to target
10:18:59 : Sending Read command and its XOR:
10:18:59 : byte 0x11 sent successfully to target
10:18:59 : byte 0xEE sent successfully to target
10:18:59 : Received response from target: 0x79
10:18:59 : Sending Read address and its checksum:
10:18:59 : data sent successfully to target: 0x40023c1c
10:18:59 : byte 0x62 sent successfully to target
10:18:59 : Received response from target: 0x79
10:18:59 : Sending number of bytes to be read - 1 and its checksum:
10:18:59 : data sent successfully to target: 0x03
10:18:59 : byte 0xFC sent successfully to target
10:18:59 : Received response from target: 0x1f
10:18:59 : Error: Number of bytes to be be read at address: 0x40023C1C not acknowledged!
10:18:59 : Sending Read command and its XOR:
10:18:59 : byte 0x11 sent successfully to target
10:18:59 : byte 0xEE sent successfully to target
10:18:59 : Received response from target: 0x1f
10:18:59 : Error: READ command not acknowledged at address: 0x40023C1C
10:18:59 : byte 0x11 sent successfully to target
10:18:59 : byte 0xEE sent successfully to target
10:18:59 : data sent successfully to target: 0x08000000
10:18:59 : byte 0x08 sent successfully to target
10:19:01 : Disabling memory Read Protection...
10:19:01 : Sending read unprotect command and its XOR:
10:19:01 : byte 0x92 sent successfully to target
10:19:01 : byte 0x6D sent successfully to target
10:19:01 : Received response from target: 0x1f
10:19:01 : Error: Disabling memory Read Protection failed
10:19:08 : Serial Port cu.SLAB_USBtoUART is successfully opened.
10:19:08 : Sending init command: 
10:19:08 : byte 0x7F sent successfully to target
10:19:08 : Received response from target: 0x1f
10:19:08 : Error: Activating device: KO. Please, verify the boot mode configuration and check the serial port configuration. Reset your device then try again... 
10:19:16 : Serial Port cu.SLAB_USBtoUART is successfully opened.
10:19:16 : Sending init command: 
10:19:16 : byte 0x7F sent successfully to target
10:19:16 : Received response from target: 0x79
10:19:16 : Activating device: OK
10:19:16 : Sending GetID command and its XOR:
10:19:16 : byte 0x02 sent successfully to target
10:19:16 : byte 0xFD sent successfully to target
10:19:16 : Received response from target: 0x79
10:19:16 : Received response from target: 0x01042979
10:19:16 : Chip ID: 0x429 
10:19:16 : Sending Get command and its XOR:
10:19:16 : byte 0x00 sent successfully to target
10:19:16 : byte 0xFF sent successfully to target
10:19:16 : Received response from target: 0x79
10:19:16 : Received response from target: 0x0b
10:19:16 : size of bytes in the response: 11
10:19:16 : Received response from target: 0x31000102112131446373829279
10:19:16 : Full received response: 0b31000102112131446373829279
10:19:16 : byte 0x11 sent successfully to target
10:19:16 : byte 0xEE sent successfully to target
10:19:16 : data sent successfully to target: 0x08000000
10:19:16 : byte 0x08 sent successfully to target
10:19:16 : byte 0x00 sent successfully to target
10:19:16 : byte 0xFF sent successfully to target
10:19:16 : Sending GetID command and its XOR:
10:19:16 : byte 0x02 sent successfully to target
10:19:16 : byte 0xFD sent successfully to target
10:19:16 : Received response from target: 0x79
10:19:16 : Received response from target: 0x01042979
10:19:16 : byte 0x11 sent successfully to target
10:19:16 : byte 0xEE sent successfully to target
10:19:16 : data sent successfully to target: 0x08000000
10:19:16 : byte 0x08 sent successfully to target
10:19:16 : byte 0x00 sent successfully to target
10:19:16 : byte 0xFF sent successfully to target
10:19:16 : Sending Read command and its XOR:
10:19:16 : byte 0x11 sent successfully to target
10:19:16 : byte 0xEE sent successfully to target
10:19:16 : Received response from target: 0x79
10:19:16 : Sending Read address and its checksum:
10:19:16 : data sent successfully to target: 0x40023c1c
10:19:16 : byte 0x62 sent successfully to target
10:19:16 : Received response from target: 0x79
10:19:16 : Sending number of bytes to be read - 1 and its checksum:
10:19:16 : data sent successfully to target: 0x03
10:19:16 : byte 0xFC sent successfully to target
10:19:16 : Received response from target: 0x1f
10:19:16 : Error: Number of bytes to be be read at address: 0x40023C1C not acknowledged!
10:19:16 : Sending Read command and its XOR:
10:19:16 : byte 0x11 sent successfully to target
10:19:16 : byte 0xEE sent successfully to target
10:19:16 : Received response from target: 0x1f
10:19:16 : Error: READ command not acknowledged at address: 0x40023C1C
10:19:16 : byte 0x11 sent successfully to target
10:19:16 : byte 0xEE sent successfully to target
10:19:16 : data sent successfully to target: 0x08000000
10:19:16 : byte 0x08 sent successfully to target
10:19:18 : Disabling memory Read Protection...
10:19:18 : Sending read unprotect command and its XOR:
10:19:18 : byte 0x92 sent successfully to target
10:19:18 : byte 0x6D sent successfully to target
10:19:18 : Received response from target: 0x1f
10:19:18 : Error: Disabling memory Read Protection failed
10:19:25 : Error: Connection to target must be established before performing the erase command.
10:19:32 : Error: Connection to target must be established before performing the erase command.
10:19:41 : Error: Connection to target must be established before performing the erase command.
10:19:44 : Serial Port cu.SLAB_USBtoUART is successfully opened.
10:19:44 : Sending init command: 
10:19:44 : byte 0x7F sent successfully to target
10:19:44 : Received response from target: 0x79
10:19:44 : Activating device: OK
10:19:44 : Sending GetID command and its XOR:
10:19:44 : byte 0x02 sent successfully to target
10:19:44 : byte 0xFD sent successfully to target
10:19:44 : Received response from target: 0x79
10:19:44 : Received response from target: 0x01042979
10:19:44 : Chip ID: 0x429 
10:19:44 : Sending Get command and its XOR:
10:19:44 : byte 0x00 sent successfully to target
10:19:44 : byte 0xFF sent successfully to target
10:19:44 : Received response from target: 0x79
10:19:44 : Received response from target: 0x0b
10:19:44 : size of bytes in the response: 11
10:19:44 : Received response from target: 0x31000102112131446373829279
10:19:44 : Full received response: 0b31000102112131446373829279
10:19:44 : byte 0x11 sent successfully to target
10:19:44 : byte 0xEE sent successfully to target
10:19:44 : data sent successfully to target: 0x08000000
10:19:44 : byte 0x08 sent successfully to target
10:19:44 : byte 0x00 sent successfully to target
10:19:44 : byte 0xFF sent successfully to target
10:19:44 : Sending GetID command and its XOR:
10:19:44 : byte 0x02 sent successfully to target
10:19:44 : byte 0xFD sent successfully to target
10:19:44 : Received response from target: 0x79
10:19:44 : Received response from target: 0x01042979
10:19:44 : byte 0x11 sent successfully to target
10:19:44 : byte 0xEE sent successfully to target
10:19:44 : data sent successfully to target: 0x08000000
10:19:44 : byte 0x08 sent successfully to target
10:19:44 : byte 0x00 sent successfully to target
10:19:44 : byte 0xFF sent successfully to target
10:19:44 : Sending Read command and its XOR:
10:19:44 : byte 0x11 sent successfully to target
10:19:44 : byte 0xEE sent successfully to target
10:19:44 : Received response from target: 0x79
10:19:44 : Sending Read address and its checksum:
10:19:44 : data sent successfully to target: 0x40023c1c
10:19:44 : byte 0x62 sent successfully to target
10:19:44 : Received response from target: 0x79
10:19:44 : Sending number of bytes to be read - 1 and its checksum:
10:19:44 : data sent successfully to target: 0x03
10:19:44 : byte 0xFC sent successfully to target
10:19:44 : Received response from target: 0x1f
10:19:44 : Error: Number of bytes to be be read at address: 0x40023C1C not acknowledged!
10:19:44 : Sending Read command and its XOR:
10:19:44 : byte 0x11 sent successfully to target
10:19:44 : byte 0xEE sent successfully to target
10:19:44 : Received response from target: 0x1f
10:19:44 : Error: READ command not acknowledged at address: 0x40023C1C
10:19:44 : byte 0x11 sent successfully to target
10:19:44 : byte 0xEE sent successfully to target
10:19:44 : data sent successfully to target: 0x08000000
10:19:44 : byte 0x08 sent successfully to target
10:19:54 : Disabling memory Read Protection...
10:19:54 : Sending read unprotect command and its XOR:
10:19:54 : byte 0x92 sent successfully to target
10:19:54 : byte 0x6D sent successfully to target
10:19:54 : Received response from target: 0x1f
10:19:54 : Error: Disabling memory Read Protection failed
10:19:56 : Serial Port cu.SLAB_USBtoUART is successfully opened.
10:19:56 : Sending init command: 
10:19:56 : byte 0x7F sent successfully to target
10:19:56 : Received response from target: 0x1f
10:19:56 : Error: Activating device: KO. Please, verify the boot mode configuration and check the serial port configuration. Reset your device then try again... 
10:20:02 : Serial Port cu.SLAB_USBtoUART is successfully opened.
10:20:02 : Sending init command: 
10:20:02 : byte 0x7F sent successfully to target
10:20:02 : Received response from target: 0x79
10:20:02 : Activating device: OK
10:20:02 : Sending GetID command and its XOR:
10:20:02 : byte 0x02 sent successfully to target
10:20:02 : byte 0xFD sent successfully to target
10:20:02 : Received response from target: 0x79
10:20:02 : Received response from target: 0x01042979
10:20:02 : Chip ID: 0x429 
10:20:02 : Sending Get command and its XOR:
10:20:02 : byte 0x00 sent successfully to target
10:20:02 : byte 0xFF sent successfully to target
10:20:02 : Received response from target: 0x79
10:20:02 : Received response from target: 0x0b
10:20:02 : size of bytes in the response: 11
10:20:02 : Received response from target: 0x31000102112131446373829279
10:20:02 : Full received response: 0b31000102112131446373829279
10:20:02 : byte 0x11 sent successfully to target
10:20:02 : byte 0xEE sent successfully to target
10:20:02 : data sent successfully to target: 0x08000000
10:20:02 : byte 0x08 sent successfully to target
10:20:02 : byte 0x00 sent successfully to target
10:20:02 : byte 0xFF sent successfully to target
10:20:02 : Sending GetID command and its XOR:
10:20:02 : byte 0x02 sent successfully to target
10:20:02 : byte 0xFD sent successfully to target
10:20:02 : Received response from target: 0x79
10:20:02 : Received response from target: 0x01042979
10:20:02 : byte 0x11 sent successfully to target
10:20:02 : byte 0xEE sent successfully to target
10:20:02 : data sent successfully to target: 0x08000000
10:20:02 : byte 0x08 sent successfully to target
10:20:02 : byte 0x00 sent successfully to target
10:20:02 : byte 0xFF sent successfully to target
10:20:02 : Sending Read command and its XOR:
10:20:02 : byte 0x11 sent successfully to target
10:20:02 : byte 0xEE sent successfully to target
10:20:02 : Received response from target: 0x79
10:20:02 : Sending Read address and its checksum:
10:20:02 : data sent successfully to target: 0x40023c1c
10:20:02 : byte 0x62 sent successfully to target
10:20:02 : Received response from target: 0x79
10:20:02 : Sending number of bytes to be read - 1 and its checksum:
10:20:02 : data sent successfully to target: 0x03
10:20:02 : byte 0xFC sent successfully to target
10:20:02 : Received response from target: 0x1f
10:20:02 : Error: Number of bytes to be be read at address: 0x40023C1C not acknowledged!
10:20:02 : Sending Read command and its XOR:
10:20:02 : byte 0x11 sent successfully to target
10:20:02 : byte 0xEE sent successfully to target
10:20:02 : Received response from target: 0x1f
10:20:02 : Error: READ command not acknowledged at address: 0x40023C1C
10:20:02 : byte 0x11 sent successfully to target
10:20:02 : byte 0xEE sent successfully to target
10:20:02 : data sent successfully to target: 0x08000000
10:20:02 : byte 0x08 sent successfully to target
10:21:24 : Error: Connection to target must be established before performing the read command.

fpistm · 2018-07-17T06:07:34Z

Did you set the Boot0 to 1 ?

sabas1080 · 2018-07-18T02:28:14Z

yes

fpistm · 2018-08-02T07:42:34Z

Hi @sabas1080,
there is a new version of STM32CubeProgrammer, could you try with it.
Anyway, I think I will rebuilt the stm32flasher with the fix.

fpistm · 2018-09-19T08:32:58Z

Small update, I will update soon all the current upload tools (STM32Flasher, STLink for windows and texane stlink for Linux/MacOS) to their latest version.
At this time, I could not integrate the STM32CubeProgrammer due to some issues (JRE,...)

fpistm · 2018-09-26T09:08:36Z

Hi @sabas1080
Tools have been updated, so Serial upload will be ok for this target using the next release
See stm32duino/Arduino_Tools#27

I think I will merge this PR as the basic support should be ok.
Are you ok @sabas1080 ?

Datasheet: http://docs.rakwireless.com/en/RAK811%20TrackerBoard/Software%20Development/RAK811%20TrackerBoard%20Datasheet%20V1.1.pdf Github: https://github.com/RAKWireless/RAK811_BreakBoard Using RAK 811 Lora Module Datasheet: http://docs.rakwireless.com/en/RAK811/Software%20Development/RAK811%C2%A0Lora%C2%A0Module%C2%A0Datasheet%C2%A0V1.3.pdf http://www.rakwireless.com/en/download/RAK811/Hardware%20Design Signed-off-by: sabas1080 <s@theinventorhouse.org>

Two version of RAK811 LoRa Tracker exist: 16Kb and 32Kb. Signed-off-by: Frederic Pillon <frederic.pillon@st.com>

Add RAK811 LoRa Tracker Board

fpistm added new variant Add support of new bard waiting feedback Further information is required labels May 20, 2018

fpistm self-assigned this May 20, 2018

fpistm mentioned this pull request May 20, 2018

Add support RAK811 #229

Closed

fpistm force-pushed the RAK811_LORA_TRACKER branch from 66d5a9c to 5545e3e Compare May 20, 2018 18:46

fpistm added the review on going label May 21, 2018

fpistm force-pushed the RAK811_LORA_TRACKER branch from 5545e3e to d788861 Compare May 24, 2018 21:27

fpistm added this to the 1.2.1/1.3.0 milestone May 28, 2018

fpistm force-pushed the RAK811_LORA_TRACKER branch 2 times, most recently from 344831c to db28efb Compare May 30, 2018 09:11

fpistm modified the milestones: 1.3.0, 1.3.1 Jun 14, 2018

fpistm force-pushed the RAK811_LORA_TRACKER branch from db28efb to 23efbf8 Compare July 10, 2018 06:22

fpistm mentioned this pull request Jul 16, 2018

RAK811 problem with radio LoRa #279

Closed

fpistm force-pushed the RAK811_LORA_TRACKER branch from 5d20be9 to 824918c Compare September 19, 2018 09:26

sabas1080 and others added 2 commits September 26, 2018 11:49

Added menu option to select RAM size

a4291d8

Two version of RAK811 LoRa Tracker exist: 16Kb and 32Kb. Signed-off-by: Frederic Pillon <frederic.pillon@st.com>

fpistm force-pushed the RAK811_LORA_TRACKER branch from 824918c to a4291d8 Compare September 26, 2018 09:52

fpistm removed waiting feedback Further information is required review on going labels Oct 1, 2018

fpistm merged commit 7799334 into stm32duino:master Oct 1, 2018

fpistm deleted the RAK811_LORA_TRACKER branch October 1, 2018 08:18

benwaffle pushed a commit to benwaffle/Arduino_Core_STM32 that referenced this pull request Apr 10, 2019

Merge pull request stm32duino#254 from fpistm/RAK811_LORA_TRACKER

40f8f68

Add RAK811 LoRa Tracker Board

Uh oh!

Conversation

fpistm commented May 20, 2018 • edited Loading Uh oh! There was an error while loading. Please reload this page.

Uh oh!

Uh oh!

sabas1080 commented May 20, 2018

Uh oh!

fpistm commented May 20, 2018

Uh oh!

chaolue commented May 23, 2018

Uh oh!

fpistm commented May 24, 2018

Uh oh!

fpistm commented May 24, 2018

Uh oh!

fpistm commented May 28, 2018

Uh oh!

sabas1080 commented May 30, 2018

Uh oh!

fpistm commented May 30, 2018

Uh oh!

fpistm commented Jun 8, 2018

Uh oh!

fpistm commented Jul 9, 2018

Uh oh!

sabas1080 commented Jul 9, 2018

Uh oh!

sabas1080 commented Jul 9, 2018

Uh oh!

fpistm commented Jul 9, 2018

Uh oh!

sabas1080 commented Jul 10, 2018 • edited Loading Uh oh! There was an error while loading. Please reload this page.

Uh oh!

Uh oh!

sabas1080 commented Jul 10, 2018

Uh oh!

fpistm commented Jul 10, 2018

Uh oh!

fpistm commented Jul 10, 2018

Uh oh!

fpistm commented Jul 10, 2018

Uh oh!

sabas1080 commented Jul 10, 2018

Uh oh!

fpistm commented Jul 11, 2018

Uh oh!

sabas1080 commented Jul 11, 2018

Uh oh!

fpistm commented Jul 11, 2018 • edited Loading Uh oh! There was an error while loading. Please reload this page.

Uh oh!

Uh oh!

sabas1080 commented Jul 13, 2018 • edited Loading Uh oh! There was an error while loading. Please reload this page.

Uh oh!

Uh oh!

fpistm commented Jul 14, 2018

Uh oh!

sabas1080 commented Jul 14, 2018

Uh oh!

sabas1080 commented Jul 15, 2018

Uh oh!

fpistm commented Jul 15, 2018

Uh oh!

sabas1080 commented Jul 15, 2018

Uh oh!

fpistm commented Jul 15, 2018

Uh oh!

fpistm commented Jul 16, 2018

Uh oh!

sabas1080 commented Jul 16, 2018

Uh oh!

sabas1080 commented Jul 16, 2018

Uh oh!

fpistm commented Jul 17, 2018

Uh oh!

sabas1080 commented Jul 18, 2018

Uh oh!

fpistm commented Aug 2, 2018

Uh oh!

fpistm commented Sep 19, 2018

Uh oh!

fpistm commented May 20, 2018 •

edited

Loading

sabas1080 commented Jul 10, 2018 •

edited

Loading

fpistm commented Jul 11, 2018 •

edited

Loading

sabas1080 commented Jul 13, 2018 •

edited

Loading