MIPS: Loongson64: env: Fixup serial clock-frequency when using LEFImips-next

When booting from LEFI firmware, the devicetree is chosen by matching
bridge type and CPU PRID. However, serials on Loongson devices may not
have the same clock frequency across different boards. For example,
CPU UARTs found on Loongson 3A4000 is supplied by the system clock,
which may be either 25MHz or 100MHz.

Luckily, LEFI firmware interface provides information about UART
address and corresponding clock frequency. Let's fixup clock-frequency
properties for serials after FDT selection by matching FDT nodes with
addresses provided by firmware.

Signed-off-by: Yao Zi <me@ziyao.cc>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

1 files changed, 98 insertions, 0 deletions

diff --git a/arch/mips/loongson64/env.c b/arch/mips/loongson64/env.c
index be8d2ad10750fb..11ddf02d6a1586 100644
--- a/arch/mips/loongson64/env.c
+++ b/arch/mips/loongson64/env.c
@@ -16,6 +16,7 @@
 
 #include <linux/dma-map-ops.h>
 #include <linux/export.h>
+#include <linux/libfdt.h>
 #include <linux/pci_ids.h>
 #include <linux/string_choices.h>
 #include <asm/bootinfo.h>
@@ -57,6 +58,101 @@ void __init prom_dtb_init_env(void)
 		loongson_fdt_blob = (void *)fw_arg2;
 }
 
+static int __init lefi_fixup_fdt_serial(void *fdt, u64 uart_addr, u32 uart_clk)
+{
+	int node, len, depth = -1;
+	const fdt64_t *reg;
+	fdt32_t *clk;
+
+	for (node = fdt_next_node(fdt, -1, &depth);
+	     node >= 0 && depth >= 0;
+	     node = fdt_next_node(fdt, node, &depth)) {
+		reg = fdt_getprop(fdt, node, "reg", &len);
+		if (!reg || len <= 8 || fdt64_ld(reg) != uart_addr)
+			continue;
+
+		clk = fdt_getprop_w(fdt, node, "clock-frequency", &len);
+		if (!clk) {
+			pr_warn("UART 0x%llx misses clock-frequency property\n",
+				uart_addr);
+			return -ENOENT;
+		} else if (len != 4) {
+			pr_warn("UART 0x%llx has invalid clock-frequency property\n",
+				uart_addr);
+			return -EINVAL;
+		}
+
+		fdt32_st(clk, uart_clk);
+
+		return 0;
+	}
+
+	return -ENODEV;
+}
+
+static void __init lefi_fixup_fdt(struct system_loongson *system)
+{
+	static unsigned char fdt_buf[16 << 10] __initdata;
+	struct uart_device *uartdev;
+	bool is_loongson64g;
+	u64 uart_base;
+	int ret, i;
+
+	ret = fdt_open_into(loongson_fdt_blob, fdt_buf, sizeof(fdt_buf));
+	if (ret) {
+		pr_err("Failed to open FDT to fix up\n");
+		return;
+	}
+
+	is_loongson64g = (read_c0_prid() & PRID_IMP_MASK) == PRID_IMP_LOONGSON_64G;
+
+	for (i = 0; i < system->nr_uarts; i++) {
+		uartdev = &system->uarts[i];
+
+		ret = lefi_fixup_fdt_serial(fdt_buf, uartdev->uart_base,
+					    uartdev->uartclk);
+		/*
+		 * LOONGSON64G's CPU serials are mapped to two different
+		 * addresses, one full-featured but differs from
+		 * previous generations, one fully compatible with them.
+		 *
+		 * It's unspecified that which mapping should uart_base refer
+		 * to, thus we should try fixing up with both.
+		 */
+		if (ret == -ENODEV && is_loongson64g) {
+			switch (uartdev->uart_base) {
+			case 0x1fe00100:
+				uart_base = 0x1fe001e0;
+				break;
+			case 0x1fe00110:
+				uart_base = 0x1fe001e8;
+				break;
+			case 0x1fe001e0:
+				uart_base = 0x1fe00100;
+				break;
+			case 0x1fe001e8:
+				uart_base = 0x1fe00110;
+				break;
+			default:
+				pr_err("Unexpected UART address 0x%llx passed by firmware\n",
+				       uartdev->uart_base);
+				ret = -EINVAL;
+				goto err_fixup;
+			}
+
+			ret = lefi_fixup_fdt_serial(fdt_buf, uart_base,
+						    uartdev->uartclk);
+		}
+
+err_fixup:
+		if (ret)
+			pr_err("Couldn't fix up FDT node for UART 0x%llx\n",
+			       uartdev->uart_base);
+	}
+
+	loongson_fdt_blob = fdt_buf;
+}
+
 void __init prom_lefi_init_env(void)
 {
 	struct boot_params *boot_p;
@@ -237,4 +333,6 @@ void __init prom_lefi_init_env(void)
 
 	if (!loongson_fdt_blob)
 		pr_err("Failed to determine built-in Loongson64 dtb\n");
+	else
+		lefi_fixup_fdt(esys);
 }